keroppets.blogg.se - Com ports not showing parallels windows

#Com ports not showing parallels windows install
#Com ports not showing parallels windows serial
#Com ports not showing parallels windows drivers
#Com ports not showing parallels windows code
#Com ports not showing parallels windows windows

Compliant with PCI Express Base Specification, Revision 1.1.

#Com ports not showing parallels windows serial

Adds 2 RS-232 9-pin serial ports and 1 ECP/EPP parallel port to your PCIe enabled system.

#Com ports not showing parallels windows install

Driver Management concluded the process to install driver silabser.inf_amd64_dfdf591955e10cae for Device Instance ID USB\VID_10C4&PID_EA60\0001 with the following status: 0x0.Cyber 2S1P PCIe Quick Installation Guide Introducing the Cyber 2S1P PCIe The Cyber 2S1P PCIe high-speed serial I/O card provides two 9-pin serial ports and one parallel port.

Driver Management has concluded the process to add Service silabser for Device Instance ID USB\VID_10C4&PID_EA60\0001 with the following status: 0.Ģ2-May-20 16:09:06 - Device installed (silabser.inf_amd64_dfdf591955e10cae).

Device USB\VID_10C4&PID_EA60\0001 requires further installation.Ģ2-May-20 16:09:06 - Driver service added (silabser).

So the hub seems to be the issue.Ģ2-May-20 16:09:06 - Device install requested: However, I just tried it with an USB-C to micro cable, et voila, ESP32 functions normally.

#Com ports not showing parallels windows code

This morning, I connected the ESP32 through the hub, and the device was working! Couple hours later, tried again, same error code 10. Yeah you are right, forgot to disclose that I bought it on Aliexpress, and contacting them for these kind of problems seems pointless.Īlso, I am using an USB-hub, since my laptop has only USB-C ports. Well super-strictly said they meant the vendor of the USB-UART adapter or board that incorporates that chip… String descriptors are not available (because the device has problem code CM_PROB_FAILED_START) Endpoint Descriptor -īDescriptorType : 0x05 (Endpoint Descriptor)īEndpointAddress : 0x81 (Direction=IN EndpointID=1)ĭata (HexDump) : 07 05 81 02 40 00 00 Endpoint Descriptor -īEndpointAddress : 0x01 (Direction=OUT EndpointID=1)ĭata (HexDump) : 07 05 01 02 40 00 00 String Descriptors. Configuration Descriptor -īDescriptorType : 0x02 (Configuration Descriptor)īConfigurationValue : 0x01 (Configuration 1) IManufacturer : 0x01 (String Descriptor 1) IdVendor : 0x10C4 (Silicon Laboratories, Inc.) Device Descriptor -īDescriptorType : 0x01 (Device Descriptor)īDeviceClass : 0x00 (defined by the interface descriptors) Connection Information V2 -ĭevIsOpAtSsOrHigher : 0 (Is not operating at SuperSpeed or higher)ĭevIsSsCapOrHigher : 0 (Is not SuperSpeed capable or higher)ĭevIsOpAtSsPlusOrHigher : 0 (Is not operating at SuperSpeedPlus or higher)ĭevIsSsPlusCapOrHigher : 0 (Is not SuperSpeedPlus capable or higher)ĭata (HexDump) : 01 00 00 00 10 00 00 00 03 00 00 00 00 00 00 00. Connection Information -Ĭonnection Status : 0x01 (DeviceConnected) Power State : D3 (supported: D0, D3, wake from D0) Status : 0x01806400 (DN_HAS_PROBLEM, DN_DISABLEABLE, DN_REMOVABLE, DN_NT_ENUMERATOR, DN_NT_DRIVER) Output USBview (USB Device Tree): = USB Port1 =Ĭonnection Status : 0x01 (Device is connected)ĬompanionHubSymLnk : USB#ROOT_HUB30#7&10a4fe21&0&0#Ĭapabilities : 0x14 (Removable, UniqueID) Any ideas of what I can try to get it to work? So the device VID is 10C4 and the PID is EA60, so I believe I should be able to use the normal drivers.

#Com ports not showing parallels windows drivers

I can get the ESP32 to work on my Ubuntu system, with the drivers that come pre installed with Ubuntu.

#Com ports not showing parallels windows windows

Reinstalling drivers, rebooting, trying different USB HUBS and cables, trying the windows 7/8 drivers, nothing works. I keep getting “The device cannot start (Code 10)”. No matter what I try, I cannot get the device to work. The Silabs chip on the device has the following information: I bought a cheap ESP32 dev kit, and installed the CP210x drivers for it (found here: ). Perhaps a bit of topic on this forum, but Silabs cannot help me unfortunately, so I thought let’s give it a try.